Euromix Euroflex Paint


Euromix™ Euroflex is a high solids, acrylic based waterproofing and decorative paint coating that provides excellent flexibility, elasticity and durability on surfaces subjected to high winds, salt spray and severe weather conditions. 

Download Product Data Sheet

Download Safety Data Sheet

Product Summary


 As well as providing the colour for wall or ceiling finishes, Euromix Primers and Paints add to the functionality of the finish system. They have been chosen on the basis of their ability to enhance the appearance and serviceability of our renders, textures and plasters. 

Euromix Euroflex is most often used as the final coloured topcoat over render and texture coated surfaces to provide an effective waterproofing barrier that also breathes – allowing vapor to escape from the substrate. Substrates must be primed with Euromix Acrylic Primer prior to the application of the Euroflex. 

White in colour at the time of manufacture, Euromix Euroflex can be pigmented (tinted) to achieve a desired colour. 

Product Name

Euromix™ Euroflex Paint

Packaging

 15 litre plastic buckets. 

Appearance

In the bucket the material appears as a wet, off-white, thick liquid. 

Application


It is recommended that the Euroflex be thoroughly stirred in the bucket, using a power stirrer, prior to application.The Euroflex can be applied by brush, roller or spray in a minimum of two coats (if applying by roller it is recommended that a 6-8 mm nap roller sleeve be used) at the rate of 1.5 SQM / Litre per coat.

Allow a minimum six (6) hours drying between coats.It is imperative that a ‘wet-edge’ is maintained at all time. Ensure that there are sufficient operators available on large areas.

Do not apply Euromix Paints and Textures in windy conditions or in temperatures outside the range 10C to 30C. Keep newly coated areas protected from rain and moisture for at least twelve (12) hours, longer in the lower temperature range.

Direct exposure to rain is not the only issue – run-off or wind driven moisture can also cause coating failure!

Coverage


Average approximate spread rate for Euromix Euroflex is 25 to 30 SQM per 15 litre bucket. This will vary depending upon type, condition and porosity of the substrate, application technique and the tinted colour.

Download Product Data Sheet

Download Safety Data Sheet

WHERE TO BUY

Drying and Curing


Drying and curing of the product is affected by type, dryness and porosity of the surface, temperature, humidity, ventilation, climate conditions and application technique and therefore drying and curing can only be given as a guide (at 25C & 50% RH):

Touch Dry

Two (2) to four (4) hours. 

Recoat

Six (6) hours. 

Related Products


Euromix Primers and Paints not only provide the colour for your wall or ceiling finish, they also improve the functionality of the finish system.

Euromix Acrylic Primer

Euromix™ Acrylic Primer is an acrylic polymer primer that is designed to penetrate and seal most substrates, prior to the application of Euromix finishing coatings. Euromix Acrylic Primer can be used over off-form concrete, cement based renders, fibre cement sheeting, polystyrene, PVC brick and block work.

Euromix Euroflex Paint

Euromix™ Euroflex is a high solids, acrylic based waterproofing and decorative paint coating that provides excellent flexibility, elasticity and durability on surfaces subjected to high winds, salt spray and severe weather conditions.

Euromix Sealer Primer

Euromix™ Sealer Primer is a clear, solvent based primer and sealer, which, when applied correctly, provides a highly water-resistant penetrative film over most porous building substrates.

Euromix NPS Primer

Euromix™ Acrylic Primer is an acrylic polymer primer that is designed to penetrate and seal most substrates, prior to the application of Euromix finishing coatings. Euromix Acrylic Primer can be used over off-form concrete, cement based renders, fibre cement sheeting, polystyrene, PVC brick and block work.